<?xml version="1.0" encoding="utf-8"?>
<rss version="2.0">
  <channel>
    <title>热处理论坛 - 热处理基础知识</title>
    <link>https://rclbbs.com/forum-37-1.html</link>
    <description>Latest 20 threads of 热处理基础知识</description>
    <copyright>Copyright(C) 热处理论坛</copyright>
    <generator>Discuz! Board by Comsenz Inc.</generator>
    <lastBuildDate>Sun, 03 May 2026 09:38:01 +0000</lastBuildDate>
    <ttl>120</ttl>
    <image>
      <url>https://rclbbs.com/static/image/common/logo_88_31.gif</url>
      <title>热处理论坛</title>
      <link>https://rclbbs.com/</link>
    </image>
    <item>
      <title>已经镶嵌好的样品，在500倍下观看</title>
      <link>https://rclbbs.com/thread-620115-1-1.html</link>
      <description><![CDATA[已经镶嵌好的样品，在500倍下观看，越看越模糊，要不断的微调焦，才能看清楚，这是什么原因造成的？]]></description>
      <category>热处理基础知识</category>
      <author>钢铁金相</author>
      <pubDate>Wed, 29 Apr 2026 00:56:49 +0000</pubDate>
    </item>
    <item>
      <title>深冷金相</title>
      <link>https://rclbbs.com/thread-620112-1-1.html</link>
      <description><![CDATA[深冷后金相组织评级是依照哪一个标准去对标呢]]></description>
      <category>热处理基础知识</category>
      <author>爱学习的Coco</author>
      <pubDate>Tue, 28 Apr 2026 03:04:27 +0000</pubDate>
    </item>
    <item>
      <title>深冷工艺</title>
      <link>https://rclbbs.com/thread-620111-1-1.html</link>
      <description><![CDATA[不锈钢固溶时效+深冷处理后没有回火，后续机加工一直有变形情况，是否跟回火工艺缺失有关，同时对应每一次机加工开粗处理是不是也要加上去应力回火。这样改善是不是就不会存在应力导致的变形情况。 ...]]></description>
      <category>热处理基础知识</category>
      <author>爱学习的Coco</author>
      <pubDate>Tue, 28 Apr 2026 03:00:37 +0000</pubDate>
    </item>
    <item>
      <title>这是什么组织</title>
      <link>https://rclbbs.com/thread-620096-1-1.html</link>
      <description><![CDATA[8620h材料轴类零件渗碳淬火回火，轴直径60，距轴面8mm处心部组织，是什么组织，有f铁素体吗]]></description>
      <category>热处理基础知识</category>
      <author>ptgs</author>
      <pubDate>Sat, 25 Apr 2026 12:13:10 +0000</pubDate>
    </item>
    <item>
      <title>关于PH15-7Mo热处理</title>
      <link>https://rclbbs.com/thread-620068-1-1.html</link>
      <description><![CDATA[要求做到≥45HRC，实际原材料热处理了，只有41HRC，不小心按照GH4169做了720℃+620℃时效，怎么调整的≥45HRC]]></description>
      <category>热处理基础知识</category>
      <author>勰士</author>
      <pubDate>Tue, 21 Apr 2026 01:32:54 +0000</pubDate>
    </item>
    <item>
      <title>铸件缩松标准</title>
      <link>https://rclbbs.com/thread-620029-1-1.html</link>
      <description><![CDATA[哪位大佬有铸件缩松标准？]]></description>
      <category>热处理基础知识</category>
      <author>菜鸟yi</author>
      <pubDate>Wed, 15 Apr 2026 08:21:42 +0000</pubDate>
    </item>
    <item>
      <title>渗碳过程中会有氢气引入</title>
      <link>https://rclbbs.com/thread-619981-1-1.html</link>
      <description><![CDATA[渗碳过程，哪个过程会有氢引入，引发氢脆]]></description>
      <category>热处理基础知识</category>
      <author>钢铁金相</author>
      <pubDate>Sun, 05 Apr 2026 02:27:09 +0000</pubDate>
    </item>
    <item>
      <title>GCr15常规淬火操作，为什么表面是压应力？</title>
      <link>https://rclbbs.com/thread-619932-1-1.html</link>
      <description><![CDATA[GCr15常规淬火操作，为什么表面是压应力？不应该是表层先一步形成M，随后芯部形成M，此时，表面已经硬化了，芯部M把表面撑开，应该是拉应力才对啊！]]></description>
      <category>热处理基础知识</category>
      <author>jinxian</author>
      <pubDate>Thu, 26 Mar 2026 11:54:36 +0000</pubDate>
    </item>
    <item>
      <title>42CrMo的调质组织，怎么还有下贝氏体</title>
      <link>https://rclbbs.com/thread-619851-1-1.html</link>
      <description><![CDATA[请教下各位高工，热处理工艺860  610  尺寸50*50的试样棒，这种白色的组织 是下贝氏体吗，黑色的应该是回火索氏体，50的直径按说应该淬透了]]></description>
      <category>热处理基础知识</category>
      <author>天山剑客</author>
      <pubDate>Mon, 16 Mar 2026 08:25:05 +0000</pubDate>
    </item>
    <item>
      <title>斯派克max能不能分析C元素，会不会把c元素烧损，不准</title>
      <link>https://rclbbs.com/thread-619788-1-1.html</link>
      <description><![CDATA[斯派克max能不能分析C元素，会不会把c元素烧损，会不会不准。]]></description>
      <category>热处理基础知识</category>
      <author>两袖清风</author>
      <pubDate>Mon, 09 Mar 2026 22:48:07 +0000</pubDate>
    </item>
    <item>
      <title>美国高速钢标准ASTM A600-92A（2016）</title>
      <link>https://rclbbs.com/thread-619698-1-1.html</link>
      <description><![CDATA[美国高速钢标准ASTM A600-92A（2016），分享给大家，希望大家喜欢。钨价暴涨，希望给大家带来一些启发。]]></description>
      <category>热处理基础知识</category>
      <author>youbei</author>
      <pubDate>Sun, 01 Mar 2026 02:30:42 +0000</pubDate>
    </item>
    <item>
      <title>45#钢调质组织 先正火后 调质的</title>
      <link>https://rclbbs.com/thread-619607-1-1.html</link>
      <description><![CDATA[皮下20左右的组织，请教下各位高工，那种比较大的珠光体团是怎么形成的，还有就是这么多的先共析铁素体网，是不是调质的时候下水下的慢了，或是调质之前正火就有呢，粗大的珠光体团有没什么解决办法呢，是偏析引起的吗 ...]]></description>
      <category>热处理基础知识</category>
      <author>天山剑客</author>
      <pubDate>Mon, 26 Jan 2026 09:17:55 +0000</pubDate>
    </item>
    <item>
      <title>H13经过高温扩散、超细化、球退后的组织比较恶劣</title>
      <link>https://rclbbs.com/thread-619601-1-1.html</link>
      <description><![CDATA[该材料1250走的高温扩散，直接1220锻造，用锻造余温淬火（超细化），水冷到300-350之间回炉均温，升到860均温、保温后，降到730保温球退，金相看着组织比较恶劣，根据NADCA标准评委AS13级，请教下各位老师，这种情况是怎么造成的，，这种对后期的调质有没有影响呢，以下 ...]]></description>
      <category>热处理基础知识</category>
      <author>天山剑客</author>
      <pubDate>Sat, 24 Jan 2026 23:34:48 +0000</pubDate>
    </item>
    <item>
      <title>氮化层脆性检验</title>
      <link>https://rclbbs.com/thread-619575-1-1.html</link>
      <description><![CDATA[对于只有20微米的白亮层，氮化层脆性怎么检验，国标规定的检测力都太大了.]]></description>
      <category>热处理基础知识</category>
      <author>钢铁金相</author>
      <pubDate>Tue, 20 Jan 2026 11:27:59 +0000</pubDate>
    </item>
    <item>
      <title>20Cr材料的产品碳氮共渗淬火的硬度问题</title>
      <link>https://rclbbs.com/thread-619570-1-1.html</link>
      <description><![CDATA[本公司的产品为20Cr材料，要求热处理硬度为HV550--700  0.5kgf.  渗层深度0.15--0.25。我们检测后的硬度和渗碳深度我学习做了一个图，请各位大师帮看一下淬火的质量怎么样。]]></description>
      <category>热处理基础知识</category>
      <author>436095154</author>
      <pubDate>Mon, 19 Jan 2026 02:17:39 +0000</pubDate>
    </item>
    <item>
      <title>mov和cr12回火颜色不好看</title>
      <link>https://rclbbs.com/thread-619568-1-1.html</link>
      <description><![CDATA[回火颜色出来颜色不均匀，青一块紫一块的]]></description>
      <category>热处理基础知识</category>
      <author>1794626491</author>
      <pubDate>Sun, 18 Jan 2026 09:56:18 +0000</pubDate>
    </item>
    <item>
      <title>表面组织</title>
      <link>https://rclbbs.com/thread-619564-1-1.html</link>
      <description><![CDATA[热处理设备：易普森多用炉，热处理工艺：强渗碳势cp%1.05,温度920°，保温碳势cp%0.85,出炉前cp%0.7,温度850°，淬火温度840°，淬火油温：85°，回火180°   4h,表面氧化如图，请教，是否因为炉子老化漏气造成表面氧化，同时，烦请看看表面贝氏体、珠光体含量多少% ...]]></description>
      <category>热处理基础知识</category>
      <author>余一泓</author>
      <pubDate>Sat, 17 Jan 2026 00:49:22 +0000</pubDate>
    </item>
    <item>
      <title>关于20Cr材料的检测报告。</title>
      <link>https://rclbbs.com/thread-619559-1-1.html</link>
      <description><![CDATA[请各位大师帮看一下，20Cr材料的材质检测报告是否符合标准。]]></description>
      <category>热处理基础知识</category>
      <author>436095154</author>
      <pubDate>Fri, 16 Jan 2026 02:56:55 +0000</pubDate>
    </item>
    <item>
      <title>20#机油适合做淬火油吗</title>
      <link>https://rclbbs.com/thread-619529-1-1.html</link>
      <description><![CDATA[拉伸检验中的热处理工艺用20#机油作为淬火油合适吗？]]></description>
      <category>热处理基础知识</category>
      <author>天线麦兜</author>
      <pubDate>Tue, 13 Jan 2026 01:02:54 +0000</pubDate>
    </item>
    <item>
      <title>关于调质金相组织的求助</title>
      <link>https://rclbbs.com/thread-619461-1-1.html</link>
      <description><![CDATA[热处理工艺：淬火前工件状态：模锻的生坯，40Cr，轴叉类产品，杆部直径75mm
淬火：网带炉淬火2小时50分钟，温度850，淬火液PAG，浓度2.5-5%，水温调节设置为30°，温差不上下超过2度，装炉状态平放每行两个，单件重14kg。
回火：推盘炉回火198分钟，温度635，装炉状态每 ...]]></description>
      <category>热处理基础知识</category>
      <author>nh_hnjh@126.com</author>
      <pubDate>Thu, 08 Jan 2026 01:29:10 +0000</pubDate>
    </item>
  </channel>
</rss>